ALPS Manufacturer of Electronic Components/Parts Catalog
close
> Switches/Encoders > TACT Switch(TM)
> SKHU Series > SKHUQHE010
Related information
｜Photo ｜Dimensions ｜Land Dimensions ｜Circuit Diagram ｜Soldering Conditions ｜
｜Taping Specifications ｜

6.2×6.5mm TACT Switch™ (Surface mount) SKHU Series

Detail

Dust-proof and With Ground Terminal Type

Model No. SKHUQHE010

Type Surface mount
Operating force 1.57N
Operating direction Vertical
Travel 0.25mm
Operating life
(5mA 5V DC) 		50,000 cycles
Initial contact resistance 100mΩ max.
Stem color Brown
Stem height 3.1mm
Minimum packing unit (pcs.) Refer to taping specifications

Series type Sharp feeling type
Operating temperature range -30℃ to +85℃
Rating (max.) 50mA 12V DC
Rating (min.) 10µA 1V DC
Electrical performance Insulation resistance 100MΩ min. 100V DC
Voltage proof 250V AC for 1 minute
Durability Vibration 10 to 55 to 10Hz/min., the amplitude is 1.5mm for all the frequencies, in the 3 direction of X, Y and Z for 2 hours respectively
Environmental performance Cold -30±2℃ for 96h
Dry heat 80±2℃ for 96h
Damp heat 60±2℃, 90 to 95%RH for 96h

Photo

TACT Switch(TM)

Dimensions

TACT Switch(TM)

Land Dimensions

TACT Switch(TM)

 
Viewed from mounting face.

Circuit Diagram

TACT Switch(TM)


Soldering Conditions

Condition for Reflow
1. Heating method
Double heating method with infrared heater.
2. Temperature measurement
Thermocouple 0.1 to 0.2 Φ CA(K) or CC(T) at solder joints (copper foil surface). A heat resisting tape should be used for fix measurement.
3. Temperature profile
(1) The above temperature shall be measured on the mounting surface of a PC board. There are cases where PC board's temperature greatly differs from that of the switch, depending on the material, size, thickness of PC board's and others. Care, should be taken to prevent the switch's surface temperature from exceeding 260℃.
(2) Soldering conditions differ depending on reflow soldering machines. Prior verification of soldering condition is highly recommended.
(3) Ask us for the specifications of lead-free products.
Manual Soldering
1. Consult with us for TACT switchTM washing conditions.
2. Prevent flux penetration from the top side of the TACT switchTM.
3. Switch terminals and a PC board should not be coated with flux prior to soldering.
4. The second soldering should be done after the switch returns to normal temperature.

Taping Specifications

Taping Packaging for Auto-insertion
Reel Size
Reel Width W (mm) 13.5
Qty/reel (pcs.)
(Minimum packing unit) 		3,000
Tape dimensions
 
1. Please order products at N times the minimum packing unit (1 reel or 1 case).
2. Consult with us for a φ330 mm diameter reel.

Notes are common to this series/models.
  • For surface mount type, 1-reel is the minimum packing units. (Please see taping specifications)
  • Please place purchase orders for taping products per minimum package units (1 reel or a case). For samples limited to technical consideration, we will comply with quantity of 200 units or less. (In simplified packing: may not be mountable to some automatic inserting machines)
  • Ask us for the export packaging unit.
  • This products can be used in vehicles.
    Although these products are designed to perform over a wide operating temperature range, please ensure that you receive and read the formal delivery specifications before use.
Inquiries about Products
For more information please contact: Products Information Center.
1-7, Yukigaya-otsuka-machi, Ota-ku, Tokyo, 145-8501, Japan
Phone: +81 (3) 5499-8154
COPYRIGHT(C) 1995-2008 ALPS ELECTRIC CO.,LTD.