ALPS Manufacturer of Electronic Components/Parts Catalog
close
> Switches/Encoders > Rotary Switches
> SRRM Series > SRRM433700
Related information
｜Dimensions ｜Mounting Hole Dimensions ｜Terminal Configuration ｜Circuit Diagram ｜Shaft Style ｜
｜Attached Parts ｜

12-positions General-purpose Vertical Type Rotary Switch SRRM Series

Detail

Model No. SRRM433700

Poles 4
Positions 3
Changeover angle 30±3°
Changeover timing Shorting
Rotational torque 80±30mN·m
Actuator configuration 18-tooth serration
Actuator length L: 20mm
Minimum packing unit (pcs.) 100

Operating temperature range -10℃ to +60℃
Rating (max.)/(min.) (Resistive load) 0.25A 30V DC/50µA 3V DC
Electrical performance Contact resistance (Initial performance/After lifetime) 20mΩ max./60mΩ max.
Insulation resistance 100MΩ min. 500V DC
Voltage proof 500V AC for 1 minute
Mechanical performance Terminal strength 10N for 1 minute
Actuator strength Rotational direction 1N·m
Push direction 100N
Wobble of actuator (load at the tip of shaft: 5N) Measuring position from mounting surface 15mm
Shaft wobble (max. value) 0.25mm max.
Applicable mounting dimension 20mm
Vibration 10 to 55 to 10Hz/min., the amplitude is 1.5mm for all the frequencies, in the 3 direction of X, Y and Z for 2 hours respectively
Resistance to soldering heat Manual soldering 350±10℃, 3(+1, 0)s
Dip soldering 260±5℃, 10±1s
Durability Operating life without load 10,000 cycles 40mΩ max.
Operating life with load (Load: as ratings) 10,000 cycles, 60mΩ max.
Environmental performance Cold -20±2℃ for 96h
Dry heat 85±2℃ for 96h
Damp heat 40±2℃, 90 to 95%RH for 96h

Dimensions

Rotary Switches

Mounting Hole Dimensions

Rotary Switches

 
1. Viewed from direction A in the dimensions.
2. The following mark in the above table indicate a stopper with the shaft turned fully counterclockwise when viewed from direction A of the diagrams.

Terminal Configuration

Rotary Switches

Circuit Diagram

Rotary Switches

 
Note that the location of C terminal differs depending on the number of positions.

Shaft Style

* 18-tooth Serration Shaft
  The shaft shows the position in which it is turned fully counterclockwise.
  Details About Serration
  (1) The mold dimensions of standard serration and the dimensions of test jigs are as shown in the figure at left.
  (2) Position of the serration bottom
  When the shaft is turned fully counterclockwise, the position of the serration bottom is on the AA line.
  (3) Slitting angle
  The slitting angle (position) is not specified.

Attached Parts

Hexagonal nut (Unit: mm)
Flat washer (Unit: mm)
 
The following parts are included with the product.

Notes are common to this series/models.
  • All the axis are die casting shafts.
  • Non shorting type requires external wiring of common terminals.
  • Place your purchase order in N minimum package units (N: integer).
  • Ask us for the export packaging unit.
  • Products other than those listed in the above chart are also available. Please contact us for details.
Inquiries about Products
For more information please contact: Products Information Center.
1-7, Yukigaya-otsuka-machi, Ota-ku, Tokyo, 145-8501, Japan
Phone: +81 (3) 5499-8154
COPYRIGHT(C) 1995-2008 ALPS ELECTRIC CO.,LTD.